How to setup Cold Standby instance in AEM

How to setup cold standby instance in AEM

Environment

AEM 6.0, 6.1, 6.2, 6.3 and later versions

Setting up the Primary instance

  1. Setup a directory for the primary instance for the Cold Standby setup.
  2. In the primary instance directory, unpack AEM using command java -jar quickstart.jar -unpack
  3. Download install.zip and place inside crx-quickstart directory
  4. Extract the content of the attached install.zip archive to create an install folder.
  5. Start the primary instance with command java -jar quickstart.jar -r primary,crx3,crx3tar
  6. Wait for the instance to be up and running.
  7. Navigate to the Web Console at: http://host:port/system/console/slinglog and create a debug logger for class:
    1. org.apache.jackrabbit.oak.plugins.segment (AEM6.0-AEM6.2) or
    2. org.apache.jackrabbit.oak.segment (AEM6.3 and higher) 
    3. name the logger tarmk-coldstandby.log.
  8. Navigate to the Web Console at: http://host:port/system/console/configMgr and search for:
    1. Apache Jackrabbit Oak TarMK Cold Standby for 6.0-6.2 service to observe the mode and other configuration are correct and in accordance to primary instance.
    2. Apache Jackrabbit Oak Segment Tar Cold Standby Service for 6.3+ service to observe the mode and other configuration are correct and in accordance to primary instance.
  9. Navigate to http://host:port/system/console/status-slingsettings to confirm proper primary runmode is stated. 

Setting up the Standby instance

1. Setup a directory for the standby instance for the Cold Standby setup.

2. Shutdown the primary instance and backup the crx-quickstart directory. 

3. Restart the primary instance.

4. Copy /crx-quickstart directory from the primary instance over to standby directory

Note: This should already contain /install folder plus the other configurations

5. Search for sling.id file in /crx-quickstart directory and delete it.

6. Start the standby instance with java -jar quickstart.jar -r standby,crx3,crx3tar and wait for the instance to be up and running.

7. Navigate to the Web Console at: http://host:port/system/console/configMgr and search for:

     a. Apache Jackrabbit Oak TarMK Cold Standby for 6.0-6.2 service to observe the mode and other configuration are correct and in accordance to primary instance.

    b. Apache Jackrabbit Oak Segment Tar Cold Standby Service for 6.3+ service to observe the mode and other configuration are correct and in accordance to primary instance.

Note: If the above configuration still shows the mode as primary, change this to standby, save the configuration and restart the standby AEM instance.  This is a one-time action required at setup time since the instance was copied from primary.  

8. Navigate to http://host:port/system/console/status-slingsettings to confirm proper standby runmode is stated. 

9. Tail error.log and tarmk-coldstandby.log to see more communication between the primary and standby instance.

Verifying the Standby instance

Test the standby setup:

  1. Navigate to http://host:port/assets.html/content/dam in the primary instance and upload an image
  2. Wait for a few minutes and check the same path under standby instance.
  3. If the image is synced up, Cold Standby Setup works as expected.

If any issues arise verify the standby instance with steps below:

  1. Ensure to start the primary instance with run mode "primary".
  2. Monitor tarmk-standby.log
    Verify that a similar message like below appears: 
    *INFO* [FelixStartLevel] org.apache.jackrabbit.oak.plugins.segment.standby.store.StandbyStoreService started primary on port 8023 with allowed ip ranges [0.0.0.0-255.255.255.255].

    or 

    *INFO* [FelixStartLevel] org.apache.jackrabbit.oak.plugins.segment.standby.store.StandbyStoreService started primary on port 8023 with allowed ip ranges []. 
  3. On the primary instance, navigate to the http://host:port/system/console/jmx/ and search for "Standby" 
    The following should appear:
        Mode: primary
        Status: running
        Running: true
  4. Ensure to start standby instance in "standby" run mode
  5. Monitor tarmk-standby.log and verify that a similar message like below appears: 
    (IP address will be the same as you setup in install.standby\ org.apache.jackrabbit.oak.plugins.segment.standby.store.StandbyStoreService.config)
    *INFO* [FelixStartLevel] org.apache.jackrabbit.oak.plugins.segment.standby.store.StandbyStoreService started standby sync with 127.0.0.1:8023 at 5 sec.
    *INFO* [CM Event Dispatcher (Fire ConfigurationEvent: pid=org.apache.jackrabbit.oak.plugins.segment.standby.store.StandbyStoreService)] org.apache.jackrabbit.oak.plugins.segment.standby.store.StandbyStoreService started standby sync with 127.0.0.1:8023 at 5 sec.
  6. On the standby instance, navigate to the http://host:port/system/console/jmx/ and search for "Standby" 
    The following should appear:
         FailedRequests: 0
         SecondsSinceLastSuccess: 2
         Mode client: dd46f264-78ec-44f6-b3f6-ad339e13d1fa
         Status: running
         Running: true
  7. Back on the primary instance, navigate to the http://host:port/system/console/jmx/ and search for "Standby". Now two Standby records should appear, one for the primary as checked in #3 and another with properties like below for the standby: 
         TransferredBinariesBytes    0
         TransferredSegmentBytes    7229892
         TransferredBinaries    0
         TransferredSegments    247
         LastSeenTimestamp    Wed Oct 05 13:38:01 EDT 2016
         RemotePort    50446
         RemoteAddress    127.0.0.1

Making the Standby instance Primary

  1. Shutdown the standby instance 
  2. Start the instance with command java -jar quickstart.jar -r primary,crx3,crx3tar

Information to provide when raising a ticket

When raising a support ticket in the support portal, qualify the issue as best as possible following guidelines in the following KB article.

Furthermore, include the installfolder in zip format and tarmk-standby.log from both primary and standby instances. 

Reference Documentation

下載

 Adobe

更快、更輕鬆地獲得協助

新的使用者?